午夜时分性爱大放送网站,久久免费人成视频观看,国内熟女啪啪自拍,久久无码高潮喷水办公室,午夜a男人的天堂京东热,在线日本高清不卡免费v,久久综合无码中文字幕

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift lift cylinder Sold to Bahrain

Release time:2023-11-12 15:30:07 Hits: Current position: Home > News

This article mainly introduces:

Bahrain hydraulic cylinder,forklift lift cylinder manufacturer,forklift lift cylinder

Bahrain forklift lift cylinder

(Bahrain forklift lift cylinder,produced by Hengyu Hydraulic Cylinder Factory)

forklift lift cylinder are widely used in Bahrain,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed forklift lift cylinder for customers from Bahrain.

Introduction to forklift lift cylinder:

The repair method of the forklift lift cylinder: the repair of the forklift lift cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

The commonly used buffer structure of the forklift lift cylinder is composed of a piston boss and a forklift lift cylinder head groove. When the piston moves close to the forklift lift cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

The cavitation of the forklift lift cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the forklift lift cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

In use, the forklift lift cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the forklift lift cylinder.

Answers to some questions about forklift lift cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

How to distinguish the bucket cylinder from the bucket rod cylinder?
It can be distinguished according to its installation and connection: one end of the bucket cylinder is connected with the bucket; The rod cylinder is not connected to the bucket. The bucket refers to the bucket installed on the excavator. According to the working mode, it is divided into backhoe bucket and shovel bucket, the backhoe bucket is commonly used. The boom and bucket rod are working device of the excavator, usually called the big arm and the forearm, which are mainly used to control the digging and loading of the bucket. The arm connected to the frame is longer, so it is commonly known as the big arm, and its term is called the boom. The arms connected to the digging bucket are smaller, so they are commonly known as the lower arms, and the term is called the bucket rod, so they are commonly known as the big lower arms.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP